Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - INCOMMUNICADO

Pages: [1] 2 3 ... 12
1
Pearson 365/367 Mechanic Shop / Re: lifting Perkins 4-108 in place
« on: February 23, 2018, 05:42:43 AM »
I have done the same to replace the rear main seal. I blocked both sides or the companion way on the deck put a heavy wall inch and a half pipe across and used a chainfall. Removed the forward engine mount nuts, I didn't remove the rear mount nuts. Disconected driveshaft, transmission,bellhousing cleaned every thing did a very careful job with the new seal ( Perkins new seal) Put everything back togeather .I didn't have any leaks in the 4-108 for about fifty hours then the seal started leaking again. Looking back on that project the only thing I would have differenty is to use an after market silacone seal.                     Allen

2
Chandlery / Re: 365 ketch for sale
« on: December 02, 2017, 04:21:55 AM »
Jim there are some pictures on this site. Go to all Incommunicado post look for replacing toe rail.

3
Chandlery / 365 ketch for sale
« on: November 27, 2017, 07:14:24 AM »
Well I have messed around for two years finding reasons not to let Incommunicado go. It's time she has been good boat. Will sell her for 16,000 as is where is. email groundcrew@bellsouth.net  Thanks Allen

4
I agree with Pete, have an custom arch made. I took a look at the Kato island davits they are just like the original Pearson davits. It still comes down to where you use your boat. Inland waters the Pearson or Kato would be ok.For offshore work the stern is to low to hang a dink. Wayne with all of his offshore miles would tell you the only place for the dink is straped to the fordeck. I hope this helps. Allen

5
Chandlery / Incommunicado
« on: August 02, 2016, 08:20:33 AM »
 Well things change in life . We have now owned maintained , upgraded and loved Incommunicado for 27 years. She has been a wonderful addiction to our family. The time has come to sell her. We are asking 50,000 well worth the price. Allen

6
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 19, 2016, 07:21:15 PM »
End of Pics. Michelle W.

7
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 19, 2016, 07:20:22 PM »
One batch left to go after this.  Michelle W.

8
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 19, 2016, 07:18:25 PM »
more pics

9
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 19, 2016, 07:17:00 PM »
More pics  Michelle W.

10
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 19, 2016, 07:15:39 PM »
That worked on the first batch.  Here is the 2nd batch.  Michelle W.

11
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 19, 2016, 07:13:58 PM »
Trying once again to post.  Michelle W.

12
Forum Support / Attaching Pictures
« on: July 19, 2016, 06:14:00 PM »
Have been trying to post pictures (23 in total) but have been unable to post.  Even tried to upload only 1 picture and am unsuccessful.

13
Pearson 365/367 Yacht Club / Re: Replacing Teak Toe Rail?
« on: July 15, 2016, 06:16:41 AM »
Moon Dancer, I have replaced all of the exterior teak on Incommunicado. The job took a lot of labor and time but well worth it. I cheated by putting the boat on a trailer and taking it to my home close to my shop. I used solid teak lumber 2 1/4 x6 1/4 that I milled to finish size 15/16 . I used the old teak as patterns to be able to use all the existing screw holes. That project I finished over four years ago still no water leaks anywhere. I have pictures of the process I will post ( I will have my wife post) Good Luck It's well worth It. Allen

14
Pearson Pilothouse / Re: Pilothouse on Ebay (no affiliation)
« on: May 31, 2016, 03:11:54 PM »
I have never seen that boat but the pics were taken at the marina where we keep Incommunicado in Jacksonville Fl. Allen

15
Wayne, Here is what you need for your prop shaft. Aqualoy stainless steel A 22 82 and 3/4" X1 1/8" single taper. As far as the dampener plate I think they are the same for a 107 and a 108 . I have had three different tyrannies they all fit the dampener plate . I do hope this helps. Allen

Pages: [1] 2 3 ... 12